A Skipjack in Ireland

Collapse
X
 
  • Time
  • Show
Clear All
new posts

  • The Boattrainman
    replied
    Holes are drilled to take 6mm brass tubes and the wires for the lights (2 for the rear light and 2 for the lights in the sail).

    Click image for larger version

Name:	IMG_0843 (800x600).jpg
Views:	318
Size:	233.9 KB
ID:	119650


    The styrene surrounds are filled with epoxy, nothing new here.

    This is not really all that enjoyable, having worked hard to get an airtight WTC, drilling the end cap full of holes is bad for the nerves!


    Click image for larger version

Name:	IMG_0845 (800x600).jpg
Views:	312
Size:	215.5 KB
ID:	119651


    The Boattrainman

    Leave a comment:


  • The Boattrainman
    replied
    The servos are positioned in holes cut in the aft of the tech rack, two over and one under.

    Click image for larger version

Name:	IMG_0841 (800x600).jpg
Views:	650
Size:	238.5 KB
ID:	119610Click image for larger version

Name:	IMG_0842 (800x600).jpg
Views:	339
Size:	236.8 KB
ID:	119611


    It's going to be a busy end cap here, with three servo arms, the piston tank inlet/outlet, a12v connection for lights and the prop shaft.

    The Boattrainman


    Leave a comment:


  • The Boattrainman
    replied
    The hatch mechanism is held in place by a slot and tab mechanism and a small screw (sorry that second photo isn't great).

    I'd rather glue it in place but as Murphy's Law (another Irishman by the way!) has it, any part that you can't service will be the first to fail.


    Click image for larger version  Name:	IMG_0837 (800x600).jpg Views:	1 Size:	240.7 KB ID:	119596Click image for larger version  Name:	IMG_0838 (800x600).jpg Views:	1 Size:	191.5 KB ID:	119597


    The hatch sits flush to the hull and by having the hinge at the 3/4 point it opens by pushing down on one end.

    Click image for larger version  Name:	IMG_0839 (800x600).jpg Views:	1 Size:	212.0 KB ID:	119598Click image for larger version  Name:	IMG_0840 (800x600).jpg Views:	1 Size:	216.9 KB ID:	119599


    The Boattrainman
    Last edited by The Boattrainman; 02-07-2017, 05:12 PM.

    Leave a comment:


  • The Boattrainman
    replied
    Hi Albion,

    I did consider that round hatch, but I had put the Photo-etched part there and didn't want to spoil that work.

    It doesn't look very prototypical when opened, I was actually surprised at the thickness of the plastic here (around 2.5mm), the access hatch looks like it's made of six inch thick steel!!!

    Rob

    Leave a comment:


  • Albion
    replied
    i cut out the round hatch just aft of the hole you, no where near big enough :(, might revisit that decision looking at your work

    Leave a comment:


  • The Boattrainman
    replied
    Hi Greevesman,

    With you 100,%, saw Bob's products, the electronic starter is a great idea.

    BUT

    As I mentioned earlier, the cost of postage and tax from the USA will put the product at around 60 plus Euro, which I can't justify for this build given the Sub kit itself cost 65 Euro. Also, I prefer mechanical On/Off switches as the boat is complete, you don't need any additional items other than the TX to operate. Here's the set up disguised on my last build.


    Click image for larger version  Name:	IMG_0835 (800x600).jpg Views:	1 Size:	286.1 KB ID:	119586Click image for larger version  Name:	IMG_0836 (800x600).jpg Views:	1 Size:	287.4 KB ID:	119587


    I prefer to think of the Sub as coming with a working forward hatch!

    Rob

    Last edited by The Boattrainman; 02-07-2017, 06:58 AM.

    Leave a comment:


  • Greevesman
    replied
    Nautilus Drydocks has a remote radio controlled on off switch. No need for a hole.

    Leave a comment:


  • The Boattrainman
    replied
    Seriously pi**ed off with Hobbyking, no sign of my order, so gone elsewhere for servos etc!!!

    In the meantime, I need access to the hull for some sort of On/Off switch, there's a hatch on the forward deck which gets opened up.


    Click image for larger version  Name:	IMG_0828 (800x600).jpg Views:	1 Size:	237.7 KB ID:	119574Click image for larger version  Name:	IMG_0829 (800x600).jpg Views:	1 Size:	212.3 KB ID:	119575


    This fitting is made to go under the hatch from 1mm styrene.

    Click image for larger version  Name:	IMG_0830 (800x600).jpg Views:	1 Size:	237.6 KB ID:	119576Click image for larger version  Name:	IMG_0831 (800x600).jpg Views:	1 Size:	235.0 KB ID:	119577


    The fitting gets sides and a new hatch is made with lugs to take a 1.5mm brass hinge.

    Click image for larger version  Name:	IMG_0832 (800x600).jpg Views:	1 Size:	226.2 KB ID:	119578Click image for larger version  Name:	IMG_0834 (800x600).jpg Views:	1 Size:	212.2 KB ID:	119580


    The hatch opens and closes and is a pressure fit in the hole, which is big enough to poke a screw driver or small rod into.

    Click image for larger version  Name:	IMG_0833 (800x600).jpg Views:	1 Size:	220.3 KB ID:	119579


    I'll figure out what the access is to later, but it means I can turn some sort of main switch on without opening the hull.

    The Boattrainman
    Last edited by The Boattrainman; 02-06-2017, 05:59 PM.

    Leave a comment:


  • Scott T
    replied
    Sounds like a better test. Thanks for the update.
    Scott T

    Leave a comment:


  • He Who Shall Not Be Named
    replied
    I like your style, Rod:

    "I see your 500, and raise you 100... *****!"

    I love this kind of WIP. Informative AND reactive!

    David

    Leave a comment:


  • The Boattrainman
    replied
    How about 600ml of water and 500ml of air!!!

    The volume of the WTC with the water is now 3300ml minus 600ml, so 2700ml of space and pushing in 500ml of air is still around the 18% mark, beyond 25% there might be some issues alright.


    Click image for larger version

Name:	IMG_0827 (800x600).jpg
Views:	119
Size:	239.0 KB
ID:	119383


    Seals holding..........

    Rob

    Leave a comment:


  • Scott T
    replied
    put 500 ml of water in your WTC then see how much air can be put in

    Leave a comment:


  • The Boattrainman
    replied
    Here is the final arrangement, at the shaft end, the stuffing tube is filled with silicone grease and has a greased mini O ring at both ends that are compressed slightly so that the shaft still rotates. It a matter of getting the balance between enough compression of the mini O rings to keep the pressure in the tank and little enough so the shaft turns easily.

    Click image for larger version

Name:	image_34191.jpg
Views:	333
Size:	220.4 KB
ID:	119366


    The forward end has the valve sealed with a box of styrene filled with two-part epoxy, that solved the tiny leak. The square of velcro acts as a bump pad against the forward caswell fittings in the top hull where the WTC rests.

    Click image for larger version

Name:	image_34192.jpg
Views:	308
Size:	215.0 KB
ID:	119367

    The WTC now holds pressure with 750ml of air through the valve (50% more than the 500ml that the Piston Tank will disperse), so a good margin of safety.

    Well pleased that it works, even though the inner WTC O rings are not required (note for the next build), on to the servos etc. which I have now ordered.

    The Boattrainman


    Last edited by The Boattrainman; 02-01-2017, 11:34 AM.

    Leave a comment:


  • The Boattrainman
    replied
    A bicycle valve core is epoxied into a 9mm hole.

    Click image for larger version  Name:	IMG_0819 (800x600).jpg Views:	1 Size:	210.0 KB ID:	119300Click image for larger version  Name:	IMG_0820 (800x600).jpg Views:	1 Size:	240.5 KB ID:	119301



    I found a nice stainless dust cap with an internal O ring that will be a bit of insurance if the valve fails.

    Click image for larger version  Name:	IMG_0821 (800x600).jpg Views:	1 Size:	230.0 KB ID:	119302



    The bicycle pump pushes 78ml of air per stroke, so seven strokes is over the 500ml of the piston tank (I know it's not exact as the air will compress, where the water in the piston tank will not).

    Click image for larger version  Name:	IMG_0822 (800x600).jpg Views:	1 Size:	285.9 KB ID:	119303


    Here is the WTC under water with seven pump strokes, the stuffing tube only has a small O ring tight up against the shaft, but still lets the shaft rotate. But this is where it gets a bit weird!

    Click image for larger version  Name:	IMG_0823 (800x600).jpg Views:	1 Size:	211.0 KB ID:	119304Click image for larger version  Name:	IMG_0824 (800x600).jpg Views:	1 Size:	218.9 KB ID:	119305


    Tests with inner and outer O rings in place showed some small leaks around the rim. So to remedy this, I decided to start with the outer O rings only and fix these first. However, with just the outer O rings, there are no leaks (except a tiny leak around the outside of the stuffing tube, more epoxy).

    So it looks like I don't need the inner O rings at all..................... have to do some more tests!!!!!

    The Boattrainman
    Last edited by The Boattrainman; 01-30-2017, 05:52 PM.

    Leave a comment:


  • trout
    replied
    We are here to help each other. I am really looking forward to seeing your progress. This is exciting stuff!

    Leave a comment:

Working...