Hey Bruce! Lookin good! I would like to come down(way down) and run with you, but Austrailia is just a wee bit too far for the likes of me. At anyrate those Rock Crawler motors start at 35 turn and go up. Way too slow in the RPM dept. for that sub. May I suggest you go back to the Caswell/Merriman supplied twister. Youll be much happier with its get up and go! Cheers!
Revell 1/72 Skipjack class USS Shark SSN591
Collapse
X
-
-
Thanks for the feed-back, Bruce. Much appreciated.
You need any parts from me? List 'em and I'll blast them off to you. Don't know about your current motor, but the one you yanked was already spark-suppressed (internal cap's), and is very high-torque. Consider putting that sucker back in there.
Glad the new snorkel induction float-valve is getting it done. The SD staying dry for you?
M
SD only had a tiny amount of water in it after second run (prehaps equal to 3 peas in volume)
I am ok for bits at the moment mate thank you for the offer!!
got to dash off to work......
BruceComment
-
Go to work!
MWho is John Galt?Comment
-
-
I haven't logged on for a while been side tracked working on my LHA.....! So I finds a shiny new website!! Swweeeeettt.....well done !
USS Shark will be getting a systems check this weekend in readiness for an OZ day deployment on the 26th...
Cheers BruceComment
-
Finally had a chance to do some work on the SHARK over the weekend!! gave it a good clean before painting the orange (escape hatch's??) deck section on Sat. Then did the hull no's and depth markings Sunday night. Will be doing a clear coat on Wednesday when I have my day off!! here are a couple of pix...
Will do some waterline weathering once clear coat has had a good chance to dry....2 PhotosComment
-
-
Yes on the photo etch. You will find them on this page here:http://sub-driver.com/index.php/acce...etch-kits.html
Great looking boat by the way. I love the extra bumps.IT TAKES GREAT INTELLIGENCE TO FAKE SUCH STUPIDITY!Comment
-
Yes on the photo etch. You will find them on this page here:http://sub-driver.com/index.php/acce...etch-kits.html
Great looking boat by the way. I love the extra bumps.Comment
-
Comment
-
I have drilled out the holes for now...will have a crack at contacting Moebius about some PE bits....
Did some pre running maintenance and some weathering before a run a weekend back (before the weather went back to winter mode...) but had to macgyver a repair when the sailplane dogbone part snapped thru the grub screw! My repair is much stronger..... C pic
Cheers Bruce4 PhotosComment
-
Good idea on the terminal blocks. Nice little pond you have for sailingIT TAKES GREAT INTELLIGENCE TO FAKE SUCH STUPIDITY!Comment
-
Last weekend had the Shark down at Naracoorte for our TF72 National regatta we had 3 proper subs (a HMS Trafalgar, USS Cheyenne and my USS Shark) this year and one surface running I53.
Phil's USS Cheyenne SSN773
Got all my surface fleet setup then got Shark ready for a cruise with Cheyenne sent her off and she just did not want to stay under kept porpoising. So I brought her back in for a check and seem ok.....sent her back out finally got her to dive.....then started to have motor cutting in and out (still had signal cause I could see rudders moving when I tweaked controls), then she decided the bottom looked nice and comfy, refusing to come back up!! It was at this point that I had enuff and switched the Tx off....and waited to see if the failsafe would kick in!! After about 30secs the boat began to slowly come up....and I mean very slowly!! When it surfaced I switched Tx back on and steered her straight back to me for drydocking.
USS Shark SSN591 shortly before troubles began...
Haig's HMS Trafalgar
Back on the table opened her up to find motor compartment with water 3/4up the motor!! popped her open to dry out, and there she sat for rest of the day. Now that everything is dried out it looks like the either the airpump or the circuit on airpump is non functional.
Had a look on the new webstore but can't seem to find the circuit that goes on the airpump?? Who make that??
Cheers BruceComment
Comment