That didn't take long
Collapse
X
-
-
I just printed off the stern of Arcturus and am in the process of printing the rest. Just too darned cool not to build up, at least as a completed hull.
The stern is a bit of a challenge, as the outputs are rectangular and not super friendly to round propellers. I'll take a closer look and post up a video of some thoughts. I'm thinking this would be a great candidate for a high flow bilge pump for propulsion...
Bob
I am just about ready to start my Arcturus build, and in fact I am just getting ready to install a fresh new roll of white PLA for the build. I am looking forward to what you come up with as to a propulsion system for this boat.
And you are right! It is a cool looking submarine!
Rob
"Firemen can stand the heat"Leave a comment:
-
-
I just printed off the stern of Arcturus and am in the process of printing the rest. Just too darned cool not to build up, at least as a completed hull.
The stern is a bit of a challenge, as the outputs are rectangular and not super friendly to round propellers. I'll take a closer look and post up a video of some thoughts. I'm thinking this would be a great candidate for a high flow bilge pump for propulsion...
BobLeave a comment:
-
-
-
Do not sail into the "need" for another submarine minefield, it is not about "need" my brothers! No less than the Constitution of these United States guarantees us the right to a Navy, see Article I, Section 8, Clause 13. Of course the definition of "us" may need some clarity...
The reference to the "Need" in my statement was actually my wife stating to me, do you really need another submarine? And that was after she came into my man cave, looked around at 18 + submarines and profoundly made that statement! But I as the humble servant that I am went down on bent knee and convinced her of that "need"! :-)) I then proceeded to Nautilus Drydocks and ordered the files for the "Arcturus"
Actually guys, my wife is a big fan and a wonderful supporter of my hobby & I love her for it!
Rob
"Firemen can stand the heat"Leave a comment:
-
Do not sail into the "need" for another submarine minefield, it is not about "need" my brothers! No less than the Constitution of these United States guarantees us the right to a Navy, see Article I, Section 8, Clause 13. Of course the definition of "us" may need some clarity...Leave a comment:
-
I’m not a master at anything, except shooting. I have a room full of trophies and medals from contests, including first place in the police academy. You and many others here hold my sincere admiration on building rc subs. RC surface craft, I’m good at. Subs, meh. It’s all the prefabricated stuff I have trouble with. Lexan tubes, ballast systems, stuff like that. I can and have built kits from before 1982. Other than the electronics, which I can do blindfold, It’s the guts that I hate. PS, You a good friend too.
Rob
"Firemen can stand the heat"Leave a comment:
-
Casey,
I truly enjoy going back and forth with you, And always in the FRIENDLIEST OF MANNERS!!
There is no doubt in my mind that you have some really nice boats that actually go under water with full ballast systems, which I have yet to achieve! I know that you are a master builder.
Regards Casey. You are a good friend!
Rob
"Firemen can stand the heat"Last edited by Das Boot; 10-30-2022, 08:19 PM.Leave a comment:
-
Casey,
I truly enjoy going back and forth with you, And always in the FRIENDLIEST OF MANNERS!!
There is no doubt in my mind that you have some really nice boats that actually go under water with full ballast systems, which I have yet to achieve! I know that you are a master builder.
Regards Casey. You are a good friend!
Rob
"Firemen can stand the heat"Leave a comment:
-
Casey,
If you are referring to the HMS Holland!
The Holland has been in the water! One time testing the WTC and setting up the boat trim!
10-09-2022, 02:04 AM
Today I put the Holland 1 together and did a quick run in the pool just to see how everything was working and checking for any leaks in the WTC!
It all went very well. I am going to add an extension onto the bottom rudder in order to give it more surface area so I can improve on the turning radius. I may need to add two pieces of foam in the upper hull just to stabilize the boat a little more.
Check out the youtube above for more in the water!! And by-the-way, I do not recall seeing ANY of your boats in the water!!
Rob
"Firemen can stand the heat"Last edited by Das Boot; 10-30-2022, 11:12 AM.Leave a comment:
-
Leave a comment: