A Skipjack in Ireland

Collapse
X
 
  • Time
  • Show
Clear All
new posts

  • The Boattrainman
    replied
    There is a great story about Vic Green, one of the greatest professional Model Locomotive builders ever, his 1/35 Scale British locos go for many tens of thousands of pounds and were only available to 'rich' clients with large cheque books.

    When questioned about the high cost of each item, he explained that as well as the hours needed to construct the models from scratch (which if billed by the hour would mean the items would be even beyond the well resourced), he rejected about two-thirds of his work as not up to standard, I think in his career he built under 50 locomotives. One of his masterworks is below.

    Click image for larger version

Name:	9f%20vg[1].jpg
Views:	128
Size:	11.2 KB
ID:	114176



    While I'm not in Vic's lofty league, I've decided the sail is just not good enough. The difference between the vents/access hatches using the Photoetched parts and original Revell scribed ones are too different, leading to an inconsistent look. One of the key aspects of any model is that the overall model must look like similar techniques were used for the end result, and as it stands this is not the case with my sail.

    Click image for larger version

Name:	IMG_0632 (800x600).jpg
Views:	305
Size:	34.6 KB
ID:	114177


    So this will have to go in the bin.

    The Boattrainman
    Last edited by The Boattrainman; 05-08-2016, 06:52 AM.

    Leave a comment:


  • The Boattrainman
    replied
    Occasionally you come across a blemish in a horrendous location. This nick around 2mm wide was in one of the rear dive planes, filler won't work here as the insertion of the dive plane axle will eventually destroy such a repair.

    Click image for larger version

Name:	IMG_0623 (800x600).jpg
Views:	342
Size:	33.4 KB
ID:	114140 Click image for larger version

Name:	IMG_0624 (800x600).jpg
Views:	329
Size:	33.3 KB
ID:	114141


    To fix it, the nick was filed out to a roughly square shape and using a scrap metal bar inserted in the axle hole as a backing, a small fillet of Plasticard loaded with thick Superglue is inserted into the enlarged hole. The metal bar is pulled down the hole before the glue sets, leaving the fillet intact.

    Click image for larger version

Name:	IMG_0626 (800x600).jpg
Views:	311
Size:	35.9 KB
ID:	114142 Click image for larger version

Name:	IMG_0627 (800x600).jpg
Views:	313
Size:	35.2 KB
ID:	114143


    The fillet is carefully cut back, and before final sanding a small amount of very thin Superglue spread around it and then sanded back to the shape of the plane.

    Click image for larger version

Name:	IMG_0628 (800x600).jpg
Views:	329
Size:	33.4 KB
ID:	114144 Click image for larger version

Name:	IMG_0629 (800x600).jpg
Views:	319
Size:	34.9 KB
ID:	114145


    Once primed, the repair is invisible.

    The Boattrainman

    Last edited by The Boattrainman; 05-06-2016, 03:34 PM.

    Leave a comment:


  • The Boattrainman
    replied

    The main hull is now blemish free, the access door and other parts will now be 'primed'.

    Click image for larger version

Name:	IMG_0617 (800x600).jpg
Views:	319
Size:	34.6 KB
ID:	114124


    There was a lot of work to fair the large vents into the hull.

    Click image for larger version

Name:	IMG_0618 (800x600).jpg
Views:	321
Size:	30.5 KB
ID:	114125


    The main hull is now blemish free, it took three evenings work.

    Click image for larger version

Name:	IMG_0620 (800x600).jpg
Views:	310
Size:	36.8 KB
ID:	114126


    The Boattrainman

    Leave a comment:


  • The Boattrainman
    replied
    To try to solve the flat line around the seam, I've stuck a double thickness line of masking tape either side of the seam one on top of the other, and filled the gap with filler. When the tapes are removed this leaves a ridge of filler.


    Click image for larger version

Name:	image_31953.jpg
Views:	345
Size:	37.9 KB
ID:	114100 Click image for larger version

Name:	image_31954.jpg
Views:	334
Size:	33.7 KB
ID:	114101


    This ridge is sanded into the hull but the centre is left alone reinstating the curve, plus I have hard sanded the top of the nose back to get the shape totally symmetrical.

    Click image for larger version

Name:	IMG_0614 (800x600).jpg
Views:	332
Size:	30.4 KB
ID:	114102


    Because I hard sanded the nose, I lost definition of the scribed lines for the torpedo doors, I had to re-scribe the centre ones (they are a bit rough in the photo, I'll fine sand etc. later).

    Click image for larger version

Name:	IMG_0616 (800x600).jpg
Views:	331
Size:	35.2 KB
ID:	114103


    The nose (in my humble opinion) is still not 'perfect' in terms of shape, but I can live with it now.

    The Boattrainman
    Last edited by The Boattrainman; 05-03-2016, 02:56 PM.

    Leave a comment:


  • The Boattrainman
    replied
    So some good and bad news with the first of many Primer coats, which will be done with acrylic spray cans (Humbrol range).

    Click image for larger version

Name:	IMG_0601 (800x600).jpg
Views:	344
Size:	37.1 KB
ID:	114091


    The main seams have come out quite well and will need just a small amount of work, there's a seam running top to bottom here, nearly invisible.

    Click image for larger version

Name:	IMG_0608 (800x600).jpg
Views:	329
Size:	32.1 KB
ID:	114094


    The Photoetched hatches and ballast vents add nicely to the main deck.

    Click image for larger version

Name:	IMG_0609 (800x600).jpg
Views:	339
Size:	32.9 KB
ID:	114092 Click image for larger version

Name:	IMG_0610 (800x600).jpg
Views:	331
Size:	34.0 KB
ID:	114093


    The scratchbuilt inlet gratings look reasonable now they have blended in.

    Click image for larger version

Name:	IMG_0606 (800x600).jpg
Views:	366
Size:	35.2 KB
ID:	114095


    However, there is a serious problem with the nose! As well as the obvious line where the two halves meet which can be filled, there is a dip along this seam resulting in the rounded shape having a flat in it around the entire nose, plus (to my eyes) the nose is slightly an odd shape, with the most forward part having a slight bulge outwards again spoiling the teardrop shape. It's not a biggy, but it will need some work to get it properly 'rounded', but it's the only flaw in what has been an excellent kit so far.

    As for the flat meeting of the two halves, I can't see any solution other than some serious filling/sanding.


    Click image for larger version

Name:	IMG_0605 (800x600).jpg
Views:	333
Size:	35.9 KB
ID:	114096

    If you enlarge the picture up a bit, you can clearly see a flat spot to the left of the torpedo doors at the seam.

    The Boattrainman
    Last edited by The Boattrainman; 05-03-2016, 04:27 PM.

    Leave a comment:


  • trout
    replied
    Well done lighting!

    Leave a comment:


  • The Boattrainman
    replied

    A final test of all the running lights is done, the wiring is led through the various guides and the sail sides and top united. An old model train controller is used to replicate the 12V running battery.

    Click image for larger version

Name:	IMG_0595 (800x600).jpg
Views:	387
Size:	34.4 KB
ID:	114063 Click image for larger version

Name:	IMG_0600 (800x600).jpg
Views:	364
Size:	39.1 KB
ID:	114062



    I'm giving some consideration to the mast light being a 'nano' LED, but I'm quite happy with the lights at this stage.

    Click image for larger version

Name:	IMG_0596 (800x600).jpg
Views:	350
Size:	39.0 KB
ID:	114064 Click image for larger version

Name:	IMG_0597 (800x600).jpg
Views:	339
Size:	39.3 KB
ID:	114065


    Time for some Primer, I find this is the only way to identify and rectify surface blemishes, of which there already many.

    The Boattrainman




    Last edited by The Boattrainman; 05-01-2016, 02:39 PM.

    Leave a comment:


  • The Boattrainman
    replied
    The sail has had all the holes opened to take the Photoetched parts. I'm just using the larger PE parts as the smaller ones are tiny.

    Click image for larger version

Name:	IMG_0593 (800x600).jpg
Views:	356
Size:	35.4 KB
ID:	114059


    The sail with the PE parts attached in the pre-drilled holes which have a backing of 0.5mm Plasticard and the hole filled with 1mm card and then the PE glued into the recess.

    Click image for larger version

Name:	IMG_0594 (800x600).jpg
Views:	299
Size:	36.6 KB
ID:	114060


    To be honest, apart from the vents on both sail sides which match my hull gratings nicely, I'm not sure the PE parts will add that much to a R/C model given the viewing distance, perhaps a super-detailed static model will benefit more, given this detail work took over a week of drilling, sanding and fettling.

    That said, there are superb parts for the port/starboard sail lights and the radar on the PE fret which could not be produced any other way.

    The Boattrainman

    Last edited by The Boattrainman; 05-01-2016, 11:52 AM.

    Leave a comment:


  • trout
    replied
    excellent mast.

    Leave a comment:


  • The Boattrainman
    replied
    Fantastic mast light, that's what I get for working from my spares box.

    Thanks for info, much appreciated.

    Rob


    Leave a comment:


  • HardRock
    replied
    Nope. This is the most frustrating bloody thing...Click image for larger version

Name:	fetch.jpg
Views:	171
Size:	93.9 KB
ID:	113999

    Leave a comment:


  • HardRock
    replied
    And when illuminated: [ATTACH=CONFIG]n93461[/ATTACH]

    Leave a comment:


  • HardRock
    replied
    Hummmmm. Image did not copy for some reason. Once more:

    Leave a comment:


  • HardRock
    replied
    Here's an option for your mast head light. [ATTACH=CONFIG]n93461[/ATTACH]

    This is a size 23 hypodermic needle, a .8 mm pico LED and a turned, clear plastic top.

    Its an easy fix to make this retract as the boat dives.

    Leave a comment:


  • He Who Shall Not Be Named
    replied
    We share a philosophy: it should make sense, in and out! I love your work, sir. OK, enough of this ... before some smart-ass suggests we get a room.

    David



    M

    Leave a comment:

Working...