Hello all,
After sheeting the sides of the hull from the gunwale down to the first stringer, I then started sheeting from the lowest stringer down to the keel. This mean't cutting out a thinner narrower strip of the 2 mm Balsa sheet. The compound curve of this sheet is less and as a result I didn't worry about the same cut and sanding technique as I used on the wider sheet that was mounted higher up. This lower sheeting also stopped two bulkheads short of the bow of the boat. This was because I needed to work on the torpedo tube positions and making the recessed sections for these.

The Torpedo tubs sections were created by making gluing down a flat rectangular strip from the bow back and parallel with the axis of the boat. I then cut out two triangular sections to glue down top and bottom to create the side of the tube sections. The torpedo tubes of this class are a real confusing area to have to build. The research is conflicted. Some drawings and photos suggest that the tubes had curves on the inside of the tube, others like the U-9 kit suggest that the tube was very rectangular. There is also evidence that there may have been a curved bulge profile behind the openings of the doors. Any clear photo's would really help,.. Anybody!!!


I then have to simply cut out and glue rectangular sheets top and bottom around the torpedo tubes. I can then add any curved surfaces later. The U-23 class only had four tubes, two bow and two stern.
To glue down the lower strips I used the same technique that I had used on the wider upper sections. Pegs, pins and glue. Sometimes where needed a little tape was introduced.

The stern section like the bow would need adding of further smaller pieces to complete the sheeting. The stern in particular would have a series of complex evolving shapes that would require the sheet to twist and turn to conform to the shape leading up to the stern post. Balsa not always wanting to conform to some complex compound curves. The join lines between the two sheets will be filled and sanded back.

Balsa is easy to pin through. However pine is rather hard. So pining into the keel wasn't easy. In some cases tape would make a less than ideal substitute. I used a fair bit of PVA glue to really secure the sheets in place.

The smaller pieces that comprise the stern. Even these short pieces have needed a twist to get them to evolve to the angles of the next Bulkhead. There will be a lot of sanding. Because I my have to sand fairly aggressively in some places, I can see that there will be points where I will probably sand through the sheet. I am considering using some expandable urethane foam behind the Balsa on the inside. This will allow me extra shaping space behind the balsa sheeting already there.

Since the sheeting has been completed i have started filling the seams between the sheets. The next task is to spend a fair amount of time checking once again for symmetry and also the subtle undulations of surfaces that may not be absolutely consistent along the length of the hull. There will be several checking techniques that I will use over the next couple of weeks.

David H
After sheeting the sides of the hull from the gunwale down to the first stringer, I then started sheeting from the lowest stringer down to the keel. This mean't cutting out a thinner narrower strip of the 2 mm Balsa sheet. The compound curve of this sheet is less and as a result I didn't worry about the same cut and sanding technique as I used on the wider sheet that was mounted higher up. This lower sheeting also stopped two bulkheads short of the bow of the boat. This was because I needed to work on the torpedo tube positions and making the recessed sections for these.
The Torpedo tubs sections were created by making gluing down a flat rectangular strip from the bow back and parallel with the axis of the boat. I then cut out two triangular sections to glue down top and bottom to create the side of the tube sections. The torpedo tubes of this class are a real confusing area to have to build. The research is conflicted. Some drawings and photos suggest that the tubes had curves on the inside of the tube, others like the U-9 kit suggest that the tube was very rectangular. There is also evidence that there may have been a curved bulge profile behind the openings of the doors. Any clear photo's would really help,.. Anybody!!!
I then have to simply cut out and glue rectangular sheets top and bottom around the torpedo tubes. I can then add any curved surfaces later. The U-23 class only had four tubes, two bow and two stern.
To glue down the lower strips I used the same technique that I had used on the wider upper sections. Pegs, pins and glue. Sometimes where needed a little tape was introduced.
The stern section like the bow would need adding of further smaller pieces to complete the sheeting. The stern in particular would have a series of complex evolving shapes that would require the sheet to twist and turn to conform to the shape leading up to the stern post. Balsa not always wanting to conform to some complex compound curves. The join lines between the two sheets will be filled and sanded back.
Balsa is easy to pin through. However pine is rather hard. So pining into the keel wasn't easy. In some cases tape would make a less than ideal substitute. I used a fair bit of PVA glue to really secure the sheets in place.
The smaller pieces that comprise the stern. Even these short pieces have needed a twist to get them to evolve to the angles of the next Bulkhead. There will be a lot of sanding. Because I my have to sand fairly aggressively in some places, I can see that there will be points where I will probably sand through the sheet. I am considering using some expandable urethane foam behind the Balsa on the inside. This will allow me extra shaping space behind the balsa sheeting already there.
Since the sheeting has been completed i have started filling the seams between the sheets. The next task is to spend a fair amount of time checking once again for symmetry and also the subtle undulations of surfaces that may not be absolutely consistent along the length of the hull. There will be several checking techniques that I will use over the next couple of weeks.
David H
Ounce again, I am seeing incredible work being done on this forum! The time consuming patience you are showing this beautiful wood build! Fantastic work David!
Rob
"Firemen can stand the heat"


Leave a comment: